Forklift Licence Australia 2026
By WhiteCard Prep Team | Last updated: November 2026 | Reading time: 12 min
A forklift licence is one of the most common high risk work licences in Australia and is used across construction, warehousing, logistics, manufacturing and agriculture. This guide explains which licence class you need, how training and assessment work, what it costs to apply, and the safety practices you will be assessed on.
Practice forklift safety questions
Our Forklift Safety topic has 66 practice questions covering pre-start checks, load capacity, and pedestrian safety.
What Is a Forklift Licence?
In Australia, operating a forklift truck requires a high risk work licence (HRWL). SafeWork NSW describes the LF class as covering a forklift truck "equipped with a mast and an elevating load carriage with a pair of fork arms or other attachment". The LF class does not cover order-picking forklift trucks, where the operator's controls rise with the load carriage. Those need the separate LO class.
The licence is issued by the work health and safety regulator in the state or territory where you live (WorkSafe Victoria issues it under Victoria's Occupational Health and Safety Regulations 2017). To apply for an LF licence you must first be assessed as competent in the unit TLILIC0003 Licence to operate a forklift truck. The order-picking (LO) class uses the unit TLILIC0004.
A licence issued in one state or territory is recognised in the others, so you do not need a separate licence to work interstate. If you move, regulators let you transfer a current licence to your new home state. HRWLs are valid for 5 years. In NSW and Victoria you can renew up to 12 months after expiry, and after that you may need to repeat the training and assessment.
Requirements for Getting a Forklift Licence
- Age: You must be at least 18 years old to be granted an HRWL
- English: Regulators require enough English to do the work safely (SafeWork NSW lists this as an eligibility requirement)
- Photo ID: You need acceptable proof of identity to enrol and again when you apply for the licence. Check your regulator's list of accepted documents
- USI: A Unique Student Identifier is required for all nationally recognised training
- White Card: While not a formal prerequisite for the forklift licence, most construction sites require both. Getting your White Card first is recommended
- Physical ability: You will need to show in the practical assessment that you can safely get on and off the forklift, use the controls and check all around you
The Training Process
Forklift training and assessment is delivered by Registered Training Organisations (RTOs). Course length depends on the RTO and on your existing experience. Many providers advertise face-to-face courses of two to three days. Training covers theory and practical work, and the assessment is done against TLILIC0003. In Victoria you must lodge your licence application with your assessment results within 60 calendar days, or you will have to repeat the assessment.
Theory Component
The theory covers:
- WHS legislation relevant to forklift operations
- Pre-operational checks and maintenance requirements
- Load assessment β understanding the data plate, rated capacity, and load centre
- Stability triangle and principles of counterbalance
- Safe operating procedures including starting, stopping, turning, and reversing
- Pedestrian safety and traffic management
- Stacking, de-stacking, and racking procedures
- Refuelling and battery charging procedures
- Emergency procedures
Practical Component
The practical assessment tests your ability to:
- Conduct a thorough pre-start (pre-operational) inspection
- Start, drive, and stop the forklift safely
- Pick up, transport, and place loads safely
- Stack and de-stack pallets at various heights
- Operate on ramps and inclines
- Navigate around obstacles and through narrow spaces
- Park and shut down the forklift correctly
How Much Does a Forklift Licence Cost?
There are two separate costs: the RTO's fee for training and assessment, and the regulator's fee for the licence itself.
- Training and assessment: Set by each RTO, so prices vary widely by provider, location and course length. Compare several RTOs and check what is included, such as the assessment and any re-assessment
- Licence application fee: Set by your state or territory regulator. For example, WorkSafe Victoria lists $77.70 per class for a new application and $58.70 for a renewal or interstate transfer (as listed in November 2026). Other regulators publish their own fee schedules, and fees usually change each financial year
- Renewal: Licences must be renewed every 5 years, and renewal also carries a regulator fee
Some employers pay for forklift training for their workers, and state-funded training may be available in some cases. Ask your employer, RTO or state training authority about what you are eligible for.
The Pre-Start Check: A Daily Requirement
Forklift operators are expected to do a pre-start (pre-operational) check before using a forklift, usually at the start of each shift. Pre-operational checks are part of the TLILIC0003 assessment. The PCBU has a legal duty to make sure plant is safe and maintained, and workplace procedures usually make the check compulsory, with a logbook or checklist to record it. A typical pre-start checklist looks like this (always follow the manufacturer's checklist for your machine):
Walk-Around Inspection
- Tyres: Check for adequate tread, correct inflation, damage, and foreign objects
- Forks: Inspect for cracks, bends, wear on the blade and heel, and proper locking in position
- Mast and chains: Check for damage, lubrication, and smooth operation
- Hydraulic system: Check hoses, cylinders, and fittings for leaks
- Fluid levels: Engine oil, coolant, hydraulic fluid, fuel/LPG/battery charge
- Overhead guard: Check for damage and secure mounting
- Data plate: Ensure it is legible and present
- General condition: Look for loose bolts, damage, or anything unusual
Operational Checks (Engine Running)
- Brakes: Test service brake and parking brake
- Steering: Check for smooth operation and no excessive play
- Mast operation: Test lift, lower, tilt forward, and tilt back
- Horn: Ensure it works
- Lights: Check headlights, tail lights, and warning lights
- Seatbelt: Check condition and operation
- Mirrors: Adjust and check for damage
- Gauges: Check all dashboard gauges for normal readings
Understanding the Stability Triangle
The stability triangle is a fundamental concept for forklift safety. On a counterbalance forklift, it is formed by three points: the two front axle ends and the rear axle pivot point. As long as the combined centre of gravity (forklift plus load) stays within this triangle, the forklift remains stable.
Several factors can shift the centre of gravity outside the triangle, causing a tip-over:
- Overloading: Exceeding the rated capacity shifts the CoG forward
- Elevated loads: Raising a load high shifts the CoG upward and forward
- Fast cornering: Centrifugal force shifts the CoG sideways
- Uneven ground: Slopes and bumps shift the CoG unpredictably
- Off-centre loads: Loads not centred on the forks shift the CoG laterally
Pedestrian Safety Around Forklifts
Collisions between forklifts and people on foot are a well-known cause of serious injury and death. Regulator guidance, such as SafeWork NSW's forklift safety guides, puts physical separation of people and forklifts first. Where that is not possible, it calls for exclusion zones and a traffic management plan. Common measures include:
- Keep pedestrians out of the forklift's operating area using exclusion zones sized to the risk assessment for that site and machine
- Establish designated pedestrian walkways separate from forklift traffic
- Use physical barriers (bollards, guardrails) to separate traffic
- Sound the horn at intersections, blind corners, and doorways
- Make eye contact with pedestrians before proceeding
- Consider warning devices such as flashing lights, reversing alarms or projected warning lights to alert pedestrians that a forklift is approaching
- Never allow passengers on a forklift (unless it has a designated passenger seat)
Forklift Types Used in Australia
The LF class covers forklift trucks with a mast and an elevating load carriage. It does not cover every machine that lifts loads on forks:
- Counterbalance forklift: The most common type with a heavy rear end to counterbalance the load on the forks
- Reach truck: Used in warehouses with narrow aisles, where the mast or forks extend forward. As mast-type forklift trucks, these generally fall under LF. Confirm with your regulator if unsure
- Rough terrain forklift: A mast-type forklift with large tyres for uneven ground on construction sites
- Order picker: The operator's controls rise with the load. This needs the LO class, not LF
- Telehandler: Not covered by the LF class, and the rules differ between states. SafeWork NSW says no HRWL is needed for a telehandler fitted with forks or a bucket, but a crane class applies when it is used with a hook and a boom-type EWP (WP) class may apply with a work platform. Victoria introduced a non-slewing telehandler class (TV) for telehandlers over 3 tonnes. Check with the regulator where you work
Refuelling and Battery Charging Safety
LPG Forklifts
- Change cylinders in a well-ventilated area away from ignition sources
- Wear gloves and eye protection (LPG can cause frostbite)
- Ensure the engine is off and the handbrake applied
- Close the cylinder valve before disconnecting
- Check for leaks after connecting the new cylinder using soapy water
Electric Forklifts
- Charge in a designated, well-ventilated area (hydrogen gas is produced during charging)
- Keep ignition sources away from the charging area
- Ensure an eye wash station is nearby (battery acid risk)
- Follow the correct charging procedure for the battery type
- Follow the battery and charger manufacturer's instructions, including any guidance on completing charge cycles
Career Opportunities for Forklift Operators
A forklift licence is useful in many industries:
- Construction: Moving materials and loading or unloading deliveries
- Warehousing and logistics: Stock management and dispatch (order picking at height needs the LO class)
- Manufacturing: Moving raw materials and finished products
- Mining: Support operations on mine sites (mining sites may have their own additional requirements)
- Agriculture: Loading and transporting produce
Pay depends on the award or agreement, the industry, the location and your other skills, so we do not quote pay rates here. For current, official earnings data on forklift drivers, see the occupation profiles from Jobs and Skills Australia or the Australian Government's Your Career website.
Sources and further reading (last reviewed November 2026)
WHS rules differ between states and change over time. Where this page states a legal or regulatory fact, it is based on the official sources below. If anything here disagrees with them, the official source wins. You can read how we check and correct our content.
- High risk work licences: classes, eligibility and renewal (SafeWork NSW)
- Forklift licences, LF and LO classes, telehandlers (SafeWork NSW)
- High risk work licence: fees, 60-day lodgement, renewal and transfer (WorkSafe Victoria)
- Non-slewing telehandler licence (TV class) (WorkSafe Victoria)
- Forklift: high risk work licence class (WorkSafe WA)
- TLILIC0003 Licence to operate a forklift truck (training.gov.au)
- Forklift safety guide for employers (PDF, SafeWork NSW)
- Your Career: occupation and pay information (Australian Government)
Prepare for Your Forklift Licence
Practice with 66 forklift safety questions plus 505+ total White Card questions.
Start Free Practice Test